Site Overlay


DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.

Author: Dojar Zuludal
Country: Singapore
Language: English (Spanish)
Genre: Career
Published (Last): 6 August 2015
Pages: 127
PDF File Size: 18.38 Mb
ePub File Size: 10.88 Mb
ISBN: 943-1-38689-366-4
Downloads: 56955
Price: Free* [*Free Regsitration Required]
Uploader: Vikazahn

Limit diode current to maximum current ratings. In either datwsheet, source-to-body diodes dh201abk be forward biased and conduct current from the signal source. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders.

Documents Flashcards Grammar checker. E and eA are measured with the leads constrained to be perpendicular to datum -C. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply. Device mounted with all leads soldered to PC board. SR Datasheet – Micropower Direct. Information furnished by Intersil is believed to be accurate and reliable.

This dimension allows for off-center lid, meniscus, and glass overrun. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. No circuit patent licenses are implied. In case of conflict between English and Metric dimensions, the inch dimensions control.

DG211 Datasheet PDF

Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2. For information regarding Intersil Corporation and its products, see www.


These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.

Putere n-am, Tu-mi fii sprijin. Parameter guaranteed by design or characterization.

DGABK (Intersil) – Quad SPST, CMOS Analog Switches, Analog Switches/Multiplexers

The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. For this configuration dimension b3 replaces dimension b2.

Measure dimension S1 at all four corners. This is a stress only rating and operation of dg201akb device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

For more information on Dg201avk values see Note 3.

For more information on TYP values see Note 2. The Datasheeet has a maximum turn-off time of ns and a maximum turn-on time of ns. Mold flash or protrusions shall not exceed 0.

Data Sheet catalog: ParNumber from digitIndex DG2

Lab 6 in this note. Dimensions b1 and c1 apply to lead base metal only. These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. VO is the steady state output with switch on. Dambar protrusions shall not exceed 0. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected.

Copyright Intersil Americas Inc. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. Typical values are for design aid only, not daasheet and not subject to production testing. The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. In the OFF state each channel blocks voltages up to the supply rails.


Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. Package Information continued The package drawing s in this data sheet may not reflect the most current specifications. Dimension Q shall be measured from the seating plane to the base plane. Asa cum sunt, la Tine vin! N is the maximum number eg201abk terminal positions. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

A notch or a pin one identification mark shall dg201agk located adjacent to pin one and shall be located within the shaded area shown. D, D1, and E1 dimensions do not include mold flash or protrusions. B1 maximum dimensions do not include dambar protrusions.

DG201ABK PDF Datasheet浏览和下载

An enable input is provided. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. Dimension M applies to lead plating and finish thickness.

Maxim reserves the right to change the circuitry and specifications without notice at any time. For the latest package outline information, go to www. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents datasueet other rights of third parties which may result from its use.