Site Overlay

MANUAL HYLSA PDF

Read the instruction manual carefully before starting the pump. • These pumps may .. vid sådana tillfällen skyddas med någon form av hylsa. • Smörj samtliga. timely basis, you may not be able to vote by giving instructions to the depositary. Imsa transaction, to refinance existing indebtness of Grupo Imsa and Hylsa. Reporte Anual , Monterrey, Mexico: Hylsa. Oslo Manual: Guidelines for Collecting and Interpreting Technological Innovation Data, 3rd Edition, Paris.

Author: Tagami Zulkigis
Country: Ethiopia
Language: English (Spanish)
Genre: Finance
Published (Last): 9 February 2014
Pages: 476
PDF File Size: 5.60 Mb
ePub File Size: 20.17 Mb
ISBN: 160-3-47259-415-9
Downloads: 25847
Price: Free* [*Free Regsitration Required]
Uploader: Kagarisar

Control and fault tracing All level sensors are factory-set for the various machines. Don’t push too far as the lip can break.

Wascomat EX S and EX S Service manual |

Coin-meter Contents Price programming The mqnual signal from X94 is compared with the signal from the rotation sensor B3 input X Disconnect the connection to the heating element to be replaced. Mount the puller screw with nut in the adaptor on the shaft.

Input from rotation sensor on motor shaft 8 When the motor is operating, a pulse train is applied on the input. The detergent is routed from the bottom of the compartment to the outer drum through the combo module immediately behind the compartment. Heating elements7 3 3. Coin-meter Hyosa the current price 3 Programming is carried out on the switch unit, where the switches correspond to values from 1 to 64 when they are set on position ON. This overload protector protects the motor during the start-up of the extraction.

  LM2940 DATASHEET PDF

Arbetsmateriallista | Karcher HKS LM User Manual | Page 83 /

Motor Description 1 Motor The motor is fitted in a bridge carrier under the outer drum. Door and door lock 4 The programme unit requests door unlocking by applying 0 V on input X92 of the door lock controller. Remove the drive belt by pulling the belt towards you while rotating the drum by hand.

Check the door safety interlock, as follows: Jumper on D is main wash function. The valve Y15 will open in main wash WN, W Replace the door lock. It locks hyllsa unlocks the door lock when the programme unit requests door locking or unlocking. Secure the hose clamp at the connection of the rubber bellows on the sleeve coupling.

Arbetsmateriallista – Karcher HKS 100 User Manual

Reattach the front cover. When pressed, any error codes are erased. Fit the new motor without locking the mounting bolts. Connect the motor cable to the motor. Turn the valve and unhook it from the bolts. Drum empty level guard closed X The compartment is divided into four sub-compartments as follows: Machine presentation When using electric heating, the water for washing is heated by three heating elements accessible maanual the front of the machine.

Control unit Jumpers are assembled on the program selector card. The heating elements and the temperature sensor are situated at the yhlsa of the outer drum close to the edge. Instruction for pulley and replacing bearings 42 6 Fig.

  APLIX 800 PDF

This will cause the slow-blow fuse to trigger.

Chisel or grind the manjal off the shaft. Improper installation or servicing of Wascomat equipment will void the manufacturer’s warranty! Instruction for pulley and replacing bearings Service Manual 5, Fig.

Door and door lock Description 1 Emergency opening arm General The door locks consists of the following: Follow all maintenance and safety procedures. Some motors are possible to change from Y to D-connection to accomodate different voltages.

Filtring till hylsa, vevhus. FM38. 1-8

Programme unit Al The steam valve is controlled by the programme unit A1. The programme unit of the machine is described in detail in section Safety precautions 1 Contents Safety precautions Push it down until it stops. When replacing the door lock, it is recommended to remove the front cover. Se section Adjustments – Drive belt tension for details. Undo the ground connection from the motor.

In order to be able to put the puller blocks under the bearing, push the rear gable a little. Every third manuap refer this service to qualified personnel May only be carried out by authorized personnel. Unlocks the door lock when the following conditions are met: